Dimmable TRIAC DALI PUSH driver 0/1-10V 8-48VDC 50W multicurrent (180-1500mA)

50W 4-in-1 Dimmable LED Driver: DALI, PUSH, TRIAC, 0/1-10V. Constant current

The SRP-TRIAC-50CC is a power supply 8-48V 4 in 1 of 50W, ENEC approved, with a constant current output of 1 channel and adjustable current from 180mA to 1500mA via DIP switches, making it suitable for various LED lights.

The TRIAC dimmer controller is designed with DALI, PUSH, TRIAC, 0/1-10V, 4 dimming interfaces in 1. 200-240V-AC. LED controller with amplitude dimming output instead of PWM output to ensure there is no flicker.

Power factor of the LED dimmer greater than 0.9 and high efficiency over 83%. Allows smooth and deep dimming down to 1% without buzzing or flickering. 1 DALI address can be automatically assigned by the DALI masters. 

Programmable with the Tridonic Software. App for users to control their individual luminaires via the Wi-Fi network.

According to the IEC 62386-101, IEC 62386-102, and IEC 62386-207 standards, this DALI controller is compatible with most DALI systems on the market. The Triac dimming driver may be compatible with universal TRIAC dimmers. When selecting the 0/1-10V interface, it is compatible with universal 0/1-10V dimmers.

Select the correct output current before wiring the LED light using the DIP switches. Make sure the power supply is disconnected before selecting the output current.

Main Features Dimmable Source TRIAC DALI PUSH 0/1-10V

• Adjustable LED driver with TRIAC/DALI/Push+0/1-10V dimming interfaces 4 in 1.
• 1 constant current output channel, maximum output power 50W.
• Output current 180mA-1500mA selectable by DIP switch.
• Allows control of single color LED lighting.
• Class II power supply, fully insulated plastic case.
• High power factor and efficiency.
• Complies with IEC standards 62386-101, 62386-102, 62386-207.
• Compatible with universal DALI masters that accept DT6 commands.
• Compatible with universal TRIAC dimmers.
• Compatible with universal 0/1-10V dimmers.
• IP20 protection rating.
• Suitable for indoor LED lighting applications.

1. Selection of the control interface

1.1. The LED driver supports 4 types of dimming input: DALI, PUSH, TRIAC, 0/1-10V.

1.2. Please select any of the 4 dimming interfaces to wire each time.

1.3. To connect a new dimming interface, the previously connected dimming interface must be disconnected.

1.4. Do not connect more than 2 (including 2) dimming interfaces simultaneously.

2. DALI address assigned by DALI masters

When connected to the DALI interface, the DALI Master controller can automatically assign a DALI address. Please refer to the user manuals of compatible DALI masters for specific operations.

3. PUSH Dimmer Mode

As long as it is connected with an AC PUSH, the controller will be in PUSH Dimmer Mode, the operations in Push Dimmer Mode are as follows:

3.1. Press the button to turn on/off.

3.2. Press and hold the button to increase or decrease the light intensity to the desired level and release it, then repeat the operation to adjust the light intensity in the opposite direction. The dimming range is from 1% to 100%.

3.3. The memory function after power off or power cut allows the device to remember the previous state before it was turned off while it is being turned on again.

4. TRIAC dimming input

When connected to a TRIAC dimmer, different TRIAC dimmers from different suppliers may have different minimum dimming levels below which the controller cannot be dimmed. To dim to 1%, make sure that the dimmer supports a minimum dimming level of 1%. 

WIRING DIAGRAM